GitHub perja12/nexa_remote_control Firmware and hardware for a custom Nexa 433 MHz controller

BrainCoding RaspberryPi and Arduino receive data from Attiny85 + 433 MhZ

433 MHz Receiver module mini breadboard Optional: 2 wire LCD There are two main libraries used to send and receive data on an Arduino platform: VirtualWire and Manchester code. As Virtualwire is a bit older, no longer supported, and supposedly can only send characters (though there is a way around that) I decided to use Manchester code.

GitHub Eistee82/ATtiny85_IR2RF433 IR reciver & RF 433MHz sender with an ATtiny85 for

2. 433 MHz Transmitter 3. DHT11 4. Attiny85 5. This is the weather stations transmitter. My version sends data from 4 sensors: Temperature, Humidity, Light, PIR. 1. dont mind this bunch of wires, it is just a flatcable that I use 7 wires of: PSU 2 wires LDR 2 wires PIR 3 wires 2. 433 MHz Transmitter 3. DHT11 4. Attiny85 5. This is the weather.

Udo's Blog "Home Automation" mit dem Arduino und 433 MHz Die komplette Fernsteuerung

Hello, I am trying to interface ATtiny85 with the cheap 433 MHz radio receiver & transmitter pair: The ATtiny is connected to receiver, Arduino UNO is connected to transmitter. The problem is: Arduino transmits the data, but ATtiny isn't responding to it (the led doesn't light up). I tried to use the newest version of VirtualWire library, but ATtiny doesn't have Timer1. The older version of.

Radio communication 433MHz with ATtiny85 KalmanLabs

433mhz Mini Low Power RF Transmitter I got a communication flow transmit/receive working between two Wemos D1 and like to outsource the transmitting part now to a ATtiny85. I used the same code as for the Wemos:

Électronique en amateur Communication RF 433 MHz entre ATTiny85 et Arduino

For his project, Erdei assembled five wireless sensors, each with the same hardware, including an ATtiny85 microcontroller, 8-pin DIP IC socket, DHT11 temperature/humidity sensor, H34A 433MHz.

433 Mhz Sender und Empfänger NIKOLAUSLUENEBURG.DE

For his project, Erdei assembled five wireless sensors, each with the same hardware, including an ATtiny85 microcontroller, 8-pin DIP IC socket, DHT11 temperature/humidity sensor, H34A 433MHz transmitter module, and a power supply with four AA batteries.

GitHub sweetpi/attiny433mhzsender AVR ATtiny85 433mhz remote control for Intertechno IT

5 SCROLL DOWN TO SEE THE SOLUTION (UPDATE II) ORIGINAL POST: I am currently building a 433MHz remote with two buttons. The remote is controlled by an Attiny85v (8MHz). Sadly it does not work very reliable, sometimes it works other times nothing happens. Here some explanations on what I did and why:

433 Mhz Sender und Empfänger NIKOLAUSLUENEBURG.DE

Temperature/Humidity sensor DHT11 0.74 $; 433MHz H34A transmitter module 0.73 $; 4xAA battery holder with switch 1$; Total 3.63 $; The receiver used for the tests is an Arduino UNO (only for testing) and a H3V4F receiving module (0.66$) with a cheap arc antenna (0.32$). Sensor-sender schematics.

USB DVBT Stick als SpektrumAnalyzer (R820T+RTL2832U) WorkisPlaying

ATtiny85, 433 RF transmitter (Can be a lot of common types, i use the Grove RF Link kit transmitter from Seeedstudio ), Logic level converter (3.3 <-> 5.0 volts (I use the one from Adafruit )), breadboard to test, bunch of breadboard wires, The source code, libraries, sketch and breadboard setup (image and fritzing): PiDome Hardware downloads.

Électronique en amateur Communication RF 433 MHz entre ATTiny85 et Arduino

Most of that is accomplished in the software but it is helped by the fact that the ATtiny85 normally runs on the 1-MHz internal clock. The rule is that lower clock frequencies require less power and 1-MHz is perfect for the transmitter logic.. You can buy them (get the correct frequency) or you can make your own. At 433-MHz, the right length.

Électronique en amateur Communication RF 433 MHz entre ATTiny85 et Arduino

attiny85 + rf 433 mhz questions - Microcontrollers - Arduino Forum attiny85 + rf 433 mhz questions juanmol August 20, 2013, 9:16am 1 hi!, i need to make wireless an analog sensor. I think i can do it with attiny and a cheap rf kit, it's possible? I mean somethink like that: TX: RX:

GitHub Eistee82/ATtiny85_IR2RF433 IR reciver & RF 433MHz sender with an ATtiny85 for

IR reciver & RF 433MHz sender with an ATtiny85 for homeautomation I'm using an Digispark ATtiny85 with an micro USB port. IR_RF.ino = Arduino Project You need RCSwitch and IRremote library Install ATtiny support to Arduino: https://digistump.com/wiki/digispark/tutorials/connecting GitHub is where people build software.

Empfangen und Senden von Daten zwischen ATtiny85 (Arduino IDE 1.06)

3 Answers Sorted by: 5 I tried those antennae and I got better range with a whip antenna made from 17cm of copper wire. Probably 1/3 to 1/2 better. Like you I'm combining an ATTiny85 and 433mhz transmitter. The transmitter definitely works better with 12V though it works quite well on 4.5V with good line of sight over about 40m for me.

ATTiny8520PU 8bit ATMEL Microcontroller

LoRa is similar to Bluetooth and WiFi in that it operates in a frequency band allocated to industrial, scientific, and medical (ISM) applications (read more about frequency allocations at this FCC link).The LoRa ISM band permitted in the U.S. is the 902-928 MHz band, while Bluetooth and WiFi operate in the 2400-2483.5 MHz and 5725-5850 MHz (5G WiFi) bands (more on the history of permitted.

GitHub perja12/nexa_remote_control Firmware and hardware for a custom Nexa 433 MHz controller

The 433 MHz ISM band is used mostly by implanted sensors and thus allows easy integration of such into the BSN. Multiple measurement scenarios have been assessed, including varying antenna orientations, transmission distances and the number of network participants. The mean packet loss rate (PLR) was 0.63% for a single slave, which is.

ATtiny85 radio controller 433MHz tutorial

Price: $1 to $2 Specifications RF 433MHz Transmitter Frequency Range: 433.92MHz Input Voltage: 3-12V Price: $1 to $2 Where to buy? You can purchase these modules for just a few dollars. Click here to compare the RF 433MHz transmitter/receiver on several stores and find the best price. Arduino with RF 433MHz Transmitter/Receiver Modules